This meter can also be used on other Ford vehicles as well, but may require either custom tuning or a different sample tube. You install your factory Ford Mass Air Meter electronics into this housing. Owners of fox body Mustangs may see a noticeable improvement in performance on both stock and modified 5.0 Mustang vehicles.
The factory 55mm unit on these vehicles flows 550 cfm and is actually 5mm smaller than the stock throttle body. The C&L 76mm unit flows nearly 800 cfm, and is a direct fit replacement for the factory 55mm unit. Dyno testing by C&L, their distributors, and the major magazines have shown that by replacing the stock unit with a C&L 76mm, you can gain as much as 11 additional rear wheel horsepower.The difference in performance on a stock engine is not primarily due to the increase in airflow, but rather through a slightly more refined calibration. A FREE security torx bit is included for sensor removal, along with installation instructions. You must re-use your stock mass air sensor in this housing.
Fuel Injectors are NOT included! One C&L 76mm Mass Airflow Housing, a 36/38# (red) sample tube, a security torx bit, and installation instructions.
Does this unit require custom tuning? Not on a stock 89-93 Mustang with 36# or 38# injectors.On other Ford applications, probably so. Can you write me a custom tune for this mass air meter? And by writing a custom tune to a chip, we do not need to size this mass air meter to your injector size. Instead, we can choose a meter size that matches the horsepower capability of your engine. Please consult me about this concept before purchasing a meter if you are interested in custom tuning. How much horsepower will this meter support? The physical size of this meter can support quite a bit of power. The electronic range of the meter is more of a limiting factor, and that range depends on what size sample tube is used, and whether or not you have a custom chip. If you are unsure about what MAF size to use, consult me before purchasing. What air filter do you recommend? We recommend you run a conical air filter bolted directly onto the front of the MAF. The 5.0L Mustangs take a 3.5" neck, 8" long conical filter. What are the dimensions of this MAF? The inside diameter is 76mm (2.99). Can this meter be used with other size injectors? Yes, but you would have to either have custom chip tuning, or use a different sample tube. Do you have a matching 76mm inlet pipe available? Does this MAF come with the sensor? The C&L design has you re-use the stock 89-93 Mustang mass airflow sensor electronics.
You simply remove two security torx bits, and swap your original sensor over to the C&L housing. Does this MAF work with the stock rubber inlet hose?It will, if you turn the outlet of the MAF down on a lathe to 3.15 O. As it is, the outlet of the MAF is 3.40 O. To match up to the thickness of a C&L 76mm inlet pipe. You can also mate this to a thin wall aluminum inlet pipe by using a reducer coupler that goes from 3.5 to the O.
Of this MAF, the I. Ask me about burning you a custom chip for this Mass Air Meter, and your Ford Racing injectors! Check out our matching 76mm Air Inlet Pipe! Note: Picture shows a machined outlet that's turned down to the stock inlet hose diameter. This meter has the as-cast 3.40 O.Outlet that is not turned down. It is best suited for mating up with the C&L 76mm aluminum inlet tube, which has about the same O. This product is brand new in the original box.
Sorry, no PO Box addresses please. The item "C&L 76mm MAF Mass Air Flow Meter Calibrated for 36/38# Injectors 86-93 Mustang" is in sale since Friday, May 01, 2015. This item is in the category "eBay Motors\Parts & Accessories\Performance & Racing Parts\Auto Performance Parts\Induction\Cold Air Intake". The seller is "pontisteve" and is located in Ocala, Florida. This item can be shipped worldwide.